混凝土搅拌车广泛用于基础、灌桩、楼板、路面、场坪、护坡、沟渠、河道、桥梁、涵洞、隧道、中小型水库等中小型工程。为了更好的使用设备，用户们在购买设备时必须要对企业的产品性能、质量及服务作深入了解，才会免除后顾之忧，那么用户们在验收混凝土搅拌，那么设备调试时必须具备以下条件：

Concrete mixers are widely used in small and medium-sized projects such as foundations, grouting piles, floors, pavements, yards, revetments, ditches, rivers, bridges, culverts, tunnels, small and medium-sized reservoirs, etc. In order to better use the equipment, users must have an in-depth understanding of the product performance, quality and service of the enterprise when purchasing the equipment, so as to avoid worries at home. Then users must have the following conditions when accepting concrete mixing, and the equipment commissioning:

1、需调试设备各部件、附件及随机东西应按标准装备齐全。

1. All parts, accessories and accompanying items of the equipment to be commissioned shall be fully equipped according to the standard.

2、备好液压油和润滑油脂，液压油的油质应符合要求。

2. Prepare hydraulic oil and lubricating grease, and the oil quality of hydraulic oil should meet the requirements.

3、按规定加注液压油、燃油、润滑油和冷却水，且液压油加至规定油面。

3. Fill hydraulic oil, fuel oil, lubricating oil and cooling water as required, and add hydraulic oil to the specified oil level.

4、应对混凝土泵进行检查、调试和试运转，使之进入正常作业状况，液压体系调试后应符合标准。

4. The concrete pump shall be inspected, debugged and test run to make it enter the normal operation condition. The hydraulic system shall meet the standard after debugging.

5、调试用混凝土搅拌车管管路管径为125。

5. The pipe diameter of concrete mixer truck for commissioning is 125.

6、实验混凝土应符合标准。

6. The experimental concrete shall meet the standard.

7、设备应安放在平整坚实的地面上。用户们除了对在购买产品时需严格检验以外，其实在日常保养问题上也是不可缺少的必要工作，这样才能达到在操作过程中使用轻松且使用寿命更长的理想效果。

7. The equipment shall be placed on a flat and solid ground. In addition to strict inspection when purchasing products, users are also indispensable and necessary work in daily maintenance, so as to achieve the ideal effect of easy use and longer service life in the process of operation.

此外平常的维护保养工作也要做好，比如：

In addition, routine maintenance work should also be done well, such as:

1.搅拌车发动机使用方法，电压多少，频率多少，才可以启动电机。启动电源，然后发动柴油机，怠速运转夏天5分钟。冬天15分钟后，升速至电压400V，频率50Hz。合上发电机空开

1. The motor can be started only after the use method, voltage and frequency of the mixer engine. Start the power supply, then start the diesel engine and idle for 5 minutes in summer. After 15 minutes in winter, speed up to 400V and 50Hz. Close the generator air switch

2.搅拌车调整切割环间隙，切割环间隙过大会导致堵S管和锥管。在料斗后方，有一个固定摇臂的大螺母，松开螺母锁片，用扳手拧死，然后再退回四分之一圈。装好锁片即可。

2. The mixer adjusts the clearance of the cutting ring, and the excessive clearance of the cutting ring will lead to the blockage of S pipe and cone pipe. At the back of the hopper, there is a big nut to fix the rocker arm. Loosen the nut lock, screw it with a wrench, and then return it for a quarter of a turn. Install the locking plate.

3.搅拌车润滑系统故障判断，润滑系统堵死，会导致分配器阀芯不动作，共有8个润滑点，如果分配器不动作，先检查主进油铜管是否畅通，不畅通则是润滑泵堵死。畅通则将8跟铜管依次拆掉，没拆一根泵送7,8次，看分配器阀芯是否动作。来判断是哪一个润滑点堵死。

3. Judging the failure of the lubrication system of the mixer truck, if the lubrication system is blocked, the distributor valve core will not act. There are 8 lubrication points in total. If the distributor does not act, first check whether the main oil inlet copper pipe is unblocked. If it is not unblocked, the lubrication pump is blocked. If it is unblocked, remove 8 copper pipes in turn, and pump 7 or 8 times without removing one to see whether the valve core of the distributor acts. To determine which lubrication point is blocked.

以上就是问题解答的相关内容了，希望能够帮助到大家。

The above is the relevant content of the question answer. I hope it can help you.